Wholesale Price China Din938 Din939 Din940 Din835 Double End Studs to Nairobi Manufacturers

See how to install a SnowSport HD Snow Plow with front hitch in this installation video. Go to https:// https://www.realtruck.com/snowsport-hd-utility-snow-plow/R181772P2014Y734MA.html to order yours today.

The installation of the SnowSport Snowplow HD is simple and easy.
Just assemble the angling interceptor to the push frame, which then attaches with a hitch pin into a 2″ front receiver hitch. Then attach the SnowSport Blade to the push frame. You’re done. Its that simple.

https://www.realtruck.com

877-216-5446

How to Install a SnowSport HD Snowplow
Video Transcript:

This video is here to help you with the assembly and mounting of your new Snow Sport HD plow.

You’ll need a receiver plow mount hitch installed on your vehicle before starting the plow assembly. Follow the written instructions in the mount kit for your particular model of truck.

To assemble and mount your Snow Sport HD, start with a quick inventory check. Use the parts diagram that came with your kit to become familiar with the pieces. Next, you’ll want to gather the tools shown on the list. Now make sure your vehicle is parked on a level grade and you’re ready to get started.

The first piece we’ll mount is the interceptor. Make sure the set collar is loose. Then slide the interceptor into the receiver hitch and secure it with a pin. There are several holes to choose from to secure it. Just make sure you leave enough room between the bumper and the interceptor to allow for the blade to angle when it’s mounted. If you need to, you can adjust this later. Slide the set collar forward and secure it with the set screw. Insert two bolts into the push frame then mount it to the interceptor. Again, you’ll notice there are several mounting holes to choose from. The objective is to have the push frame about eight to ten inches above the ground. Loosely mount the push frame into the interceptor.

Then measure both sides for accuracy. If you’re within eight to ten inches, you can add the rest of the bolts. But only tighten them to a snug fit for now. Use a bubble level to check and make sure the push frame is vertical. If you need to make an adjustment, simply loosen the bolts and add the provided shims. Now you can tighten all four bolts. Use the two by four blocks to prop up the bottom part of the aluminum blade. Then, insert the rubber blade into the channel until it’s flush with the end of the aluminum blade.

Now, move the blocks underneath the tongue and groove joint under the bottom half of the blade. Overlap the top half onto the bottom half and make sure the sections are flush. Insert two square nuts into the middle channel and slide them near the factory marks on the blade. Insert two square nuts into the top channel and slide them over near the factory marks on the blade. Align the inner side of the slide hinge to the factory mark on the blade, keeping the edge of the slide hinge in line with it’s mark. Move the square nuts so they align with the holes and insert the Allen bolts into them. Tighten all bolts. Use hex head bolts for the top half. Tighten all bolts and repeat this procedure for the other hinge. Making sure the rubber blade is flush with the aluminum, drill a 3/16th’s inch pilot hole on the four factory marks.

Drill only through the first layer of aluminum and just into the rubber. Now, run a self drilling Phillips head screw into each of those holes. Drill a 5/16th’s inch hole into the four factory marks on the tongue and groove joint. Make sure you only drill through the first two layers on the back wall of the blade and not into the front wall. Insert self threading hex head bolts into each of these holes. Hang the assembled blade onto the push frame. Insert the key hole pins to lock it into transport position. Thread a hex nut onto the stud end of the blade marker. Insert two square nuts into the channel and position the handle into place. Insert the stud end of the blade marker into the outside square nut of the handle. Line up the other square nut and insert a hex head bolt and tighten securely. Then, tighten the jam nut. Repeat this procedure for the other side.

Place metal end plate on outside of rubber box end and align it to the side of the plow. Fasten it with four long hex head self threading bolts. Tighten the bolts evenly until the rubber compresses to the blade. Repeat this procedure for the other side.

The installation is now complete. Your plow is ready for the winter season.

Company webpage: https://www.semblex.com

Our high-performance STRUX® fasteners offer a stronger and more reliable assembly alternative to traditional clinch and WELD STUDS. Along with stud applications, the STRUX® design can be used in joints that require self-tapping fasteners. In most cases, a STRUX® fastening solution can yield significant time and cost savings when compared to welded or other staked fasteners.
Insertion press equipment from Haeger recommended. Free catalog and engineering support can be found at www.semblex.com

For more product information, please visit https://www.semblex.com/Products/Details/strux.cfm

STRUX® is a registered trademarks of Acument Intellectual Properties

https://www.haeger.com/