New Fashion Design for Metal Garden WindMill Supply to America

Fun Gun Reviews Presents:The Sharps Rifle Company “Balanced Bolt Carrier” and “Relia-Bolt”. Using S7 Steel, an NP3 finish and the improved features, this is the highest quality BCG on the market. A special thanks to my good friend Robbie Wheaton of Wheaton Arms.

Sharps Rifle Co. Website: https://srcarms.com/

Wheaton Arms: https://www.wheatonarms.com/

Thanks for watching~ Sootch00

Music is from Jingle Punks Royalty Free Music through the Fullscreen Network. Used with permission.

This video will run you through the process of assembling a Manual Tension Exercise Bike. This is a general instructional video and there will be differences depending on the model you are setting up, always refer to your manual to see how to set up your particular machine. If you have any questions about your model contact the staff at Fitness Choice.

Fitness Choice
1800 22 77 88
www.fitnesschoice.com.au

This video is being created to show you how to assemble most exercise bikes that come with a manually adjusted resistance system. The model you may have may not be exactly the same so it is vital that you use your manual as the main guide for assembly. Remove the straps from the box and open it up, take out what you can from the top and then place it to the side. Here you will find the tools, these will be all you need to assemble your machine, there are also some bolts and screws. Once you’ve removed all you can from the top, carefully lay the box down and remove the straps. Cut the sides off the box so that you can open the top like a lid. Now take out the rest of the equipment. This is the instruction manual, this should be your main guide and will take you through the assembly and tips on use. It is very important that you follow the instructions in correct order. Remove the unit and stand it up. Slide bolts into the stands and place them under the base of the machine, tighten the bolts. The stand with the wheels is attached to the front of the machine. Now attach the pedals. These will only go on one way and will screw in, in different directions on either side. Use the supplied tool to tighten them. Attach the pedal straps making sure the plain side is facing up. Unscrew the bolts of the base of the arm housing. The tensioners lower knob goes in the lower clasp and the top slots in higher. Now connect the cable, it will only go together one way. As the tension knob is rotated to the right the numbers increase which means the tension will increase, this pulls on the cable lifting the tensioner and increasing the overall tension or resistance. Rotating to the left releases the pressure lowering resistance. Once that is done slide the arm onto the machine and secure the bolts. Remove the screws from the arm and attach the cup holder. Put onto the T handle a washer, then a spring washer, then the casing, then the black plastic cover followed by the metal plate. Holding the bike handles in place as shown screw this assembly some of the way onto the arm. Now onto this bolt add a spring washer, then a normal washer. Attach this to the top half of the metal, it’s okay if the black plastic is loose at this point. Swing the black plastic cover over the metal plate and push firmly. Tighten both the top bolt and the T handle. The T handle will be what you use to adjust the bike handles. Slide the seat stand into the machine and fasten with the height adjuster. To use the height adjustment knob in the future turn four times and pull out, from there you will be able to raise or lower the seat stand, then just push back in and turn back four times. Bolt the seat onto the seat plate. Remove the knob and keep track of where the plate is inside the seat plate. Reattach the seat knob through the seat stand into the seat plate. Screw on the seat side covers. Now unscrew the screws from the back of the console, unsecure the wires at the top of the bike arm, the lower wire is the heart rate monitor and will need to go through the hole in the arm and fed up to the console. Attach the cables from the console to the ones coming up through the arm. Now push the cable plug into the hole and pull the wires through so they sit tight and out of the way. Screw on the console. When moving the machine pull back on the handle bars and wheel it carefully.